View XPGWHT-L1-0000-00G51_4596265.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Cree(R) XLamp(R) XP-G LEDs
Data Sheet
The XLamp XP-G LED delivers unprecedented levels of light output and efficacy for a single die LED. The XLamp XP-G LED continues Cree's history of innovation in LEDs for lighting applications with wide viewing angle, symmetrical package, unlimited floor life and electrically neutral thermal path. XLamp XP-G LEDs are the ideal choice for lighting applications where high light output and maximum efficacy are required, such as LED light bulbs, outdoor lighting, portable lighting, indoor lighting and solar-powered lighting.
FEATURES * * * * * * * * * * Available in white and outdoor white ANSI-compatible chromaticity bins Maximum drive current: 1500 mA Low thermal resistance: 6C/W Wide viewing angle: 125 Unlimited floor life at 30C/85% RH Reflow solderable - JEDEC J-STD-020C Electrically neutral thermal path RoHS and REACH-compliant UL-recognized component (E326295)
Table of Contents
Flux Characteristics (TJ = 25C)................................................................................................................. 2 Characteristics ........................................................................................................................................ 2 Relative Spectral Power Distribution ........................................................................................................... 3 Relative Flux vs. Junction Temperature (IF = 350 mA)................................................................................... 3 Electrical Characteristics (TJ = 25C) .......................................................................................................... 4 Thermal Design ....................................................................................................................................... 4 Relative Flux vs. Current (TJ = 25C) ......................................................................................................... 5 Typical Spatial Distribution ........................................................................................................................ 5 Reflow Soldering Characteristics ................................................................................................................ 6 Notes ..................................................................................................................................................... 7 Mechanical Dimensions (TA = 25C) ........................................................................................................... 8 Tape and Reel ......................................................................................................................................... 9 Packaging ............................................................................................................................................. 10
ev 3 CLD-DS20 R Data Sheet:
Subject to change without notice. www.cree.com/xlamp
1
Flux Characteristics (TJ = 25C)
The following table provides several base order codes for XLamp XP-G LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family.
Base Order Codes Min Luminous Flux @ 350 mA (lm) Group R2 Cool White 5,000 K 8,300 K R3 R4 R5 R2 Outdoor White 4,000 K 5,300 K R3 R4 Q5 Neutral White 3,700 K 5,000 K R2 R3 Q3 Warm White 2,600 K 3,700 K Q4 Q5 Flux (lm) 114 122 130 139 114 122 130 107 114 122 93.9 100 107 XPGWHT-L1-0000-00E51 XPGWHT-L1-0000-00F51 XPGWHT-L1-0000-00G51 XPGWHT-L1-0000-00H51 XPGWHT-01-0000-00EC2 XPGWHT-01-0000-00FC2 XPGWHT-01-0000-00GC2 XPGWHT-L1-0000-00DE4 XPGWHT-L1-0000-00EE4 XPGWHT-L1-0000-00FE4 XPGWHT-L1-0000-00BE7 XPGWHT-L1-0000-00CE7 XPGWHT-L1-0000-00DE7
Color
CCT Range Min. Max.
Order Code
Notes: * Cree maintains a tolerance of +/- 7% on flux and power measurements. * Typical CRI for Cool White and Neutral White (3,700 K - 10,000 K CCT) is 75. * Typical CRI for Outdoor White (4,000 K - 5,300 K CCT) is 70. * Typical CRI for Warm White (2,600 K - 3,700 K CCT) is 80.
Characteristics
Characteristics Thermal resistance, junction to solder point Viewing angle (FWHM) Temperature coefficient of voltage ESD classification (HBM per Mil-Std-883D) DC forward current Reverse voltage Forward voltage (@ 350 mA) Forward voltage (@ 700 mA) Forward voltage (@ 1000 mA) LED junction temperature mA V V V V C 3.0 3.2 3.3 150 Unit C/W degrees mV/C Minimum Typical 6 125 -2.1 Class 2 1500 5 3.75 Maximum
* The increase of maximum forward current to 1500 mA for XLamp XP-G Cool White is retroactive and applies to all XLamp XP-G Cool White LEDs produced by Cree. The increase is the result of more extensive qualification testing that was performed after the initial product launch.
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
2
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Relative Spectral Power Distribution
100
Relative Radiant Power (%)
80
60
5000K - 8300K CCT
3700K - 5000K CCT
40
2600K - 3700K CCT
20
0 400 450 500 550 600 650 700 750
Wavelength (nm)
Relative Flux vs. Junction Temperature (IF = 350 mA)
100% 90%
Relative Luminous Flux
80% 70% 60% 50% 40% 30% 20% 10% 0% 25 50 75 100 125 150
Junction Temperature (C) Junction Temperature (C)
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
3
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Electrical Characteristics (TJ = 25C)
1500
1400 1300
1200
Forward Current (mA)
1100 1000 900 800 700 600
500
400 300
200
100 0 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75
Forward Voltage (V)
Thermal Design
The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics.
1600 1400
Maximum Current (mA)
1200 1000 800 600 400 200 0 0 20 40 60 80 100 120 140
Rj-a = 10C/W = 10C/W Rj-a = 15C/W = 15C/W Rj-a = 20C/W = 20C/W Rj-a = 25C/W = 25C/W
Ambient Temperature (C)
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
4
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Relative Flux vs. Current (TJ = 25C)
350%
Relative Luminous Flux (%)
300% 250% 200% 150%
100%
50% 0% 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
Forward Current (mA)
Typical Spatial Distribution
120
Relative Luminous Intensity (%)
100
80
60
40
20
0 -100 -80 -60 -40 -20 0 20 40 60 80 100
Angle ()
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
5
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Reflow Soldering Characteristics
In testing, Cree has found XLamp XP-G LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Preheat: Temperature Min (Tsmin) Preheat: Temperature Max (Tsmax) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25C to Peak Temperature
Lead-Based Solder 3C/second max. 100C 150C 60-120 seconds 183C 60-150 seconds 215C 10-30 seconds 6C/second max. 6 minutes max.
Lead-Free Solder 3C/second max. 150C 200C 60-180 seconds 217C 60-150 seconds 260C 20-40 seconds 6C/second max 8 minutes max.
Note: All temperatures refer to topside of the package, measured on the package body surface.
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
6
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Notes
Lumen Maintenance Projections Cree currently recommends a maximum drive current of 1000 mA for XLamp XP-G white in designs seeking the ENERGY STAR* 35,000 hour lifetime rating ( 94.1% luminous flux @ 6000 hours) or 25,000-hour lifetime rating ( 91.8% luminous flux @ 6000 hours). Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree's lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. * These lifetime ratings are based on the current ENERGY STAR Solid State Lighting Luminaires V1.1 (December 12, 2008) and ENERGY STAR Integral LED Lamps V1.0 (December 3, 2009) lumen maintenance criteria. Moisture Sensitivity In testing, Cree has found XLamp XP-G LEDs to have unlimited floor life in conditions 30C / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85C / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/ EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye.
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
7
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Mechanical Dimensions (TA = 25C)
All Measurements are .13mm unless otherwise indicated
All measurements are .13 mm unless otherwise indicated.
B
6
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND 3.2 CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC.
5
4
3
REV
2
DESC
A
Re
2.3
D
2
DRAWN BY
IRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH:
1.6
D. Seibel
CHECK
3.453.45 8/28/09
DATE DATE DATE TITLE
4600 Silicon Drive Durham, N.C 27703 Fax (919) 313-5558
2.00
A
3.30
0.58
1.3 0.5 0.5
B. Stanton
APPROVED
Phone (919) 313-5300
.73
2.30
.50
MATERIAL
XPG Top Level Customer Drawing
SIZE
FINAL PROTECTIVE FINISH SCALE
C
25.000
DRAWING NO.
2601-00005
SHEET OF
REV.
B
1 /1
3
2
1
3.453.45
C
2.6 1.30 .50
Top View
3.3 .50 2.3 0.5
Side View
1.30 .65
0.6 3.2 2.4
Bottom View
.60 1.20 .60
.50
B
.40 3.30 3.20
3.2
0.5
3.3
1.65
0.4
1.60
.40 .50
0.4 1.3 0.5
A
.40 .40
0.4 0.4 1.2
3.20
RECOMMENDED STENCIL PATTERN UNLESS OTHERWISE SPECIFIED (HATCHED AREA IS OPENING) DIMENSIONS ARE IN
3.30
PCB SOLDER PAD
RECOMMENDED Recommended PCB Solder Pad
SCALE 20.000
DRAWN BY
DATE
Recommended Stencil Pattern Shaded area is open SCALE 20.000
D. Seibel
CHECK
8/28/09
DATE
THIRD ANGLE PROJECTION
MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH:
1.6
APPROVED
DATE
MATERIAL
FINAL PROTECTIVE FINISH
6
5
4
3
2
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
8
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Tape and Reel
All dimensions in mm. 1.5.1
4.0.1 1.75.10 8.0.1
2.5.1 Cathode Side
+.3 12.0 .0
Anode Side (denoted by + and circle) User Feed Direction END START
Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.)
Loaded Pockets (1,000 Lamps)
Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) User Feed Direction
Cover Tape
Pocket Tape
13mm 7"
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
9
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Dessicant Desiccant (inside bag) (inside bag)
Packaging
Humidity Indicator Humidity Indicator Card (inside bag) (inside bag)
All dimensions in mm.
Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag
Label with Cree Bin CREE Bin Code & Barcode Label # Code, Qty, Lot Label with CREE Bin Code Cree Bin & Barcode Label Code, Qty, Lot # Labelwith CustomerBin Label with Cree P/N, Qty, Lot Lot # Code, Qty, #, PO # Label with Cree Bin Label with Customer P/N, Qty, Lot #, PO Code, Qty, Lot# #
Patent Label Patent Label Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO #
Label with Customer Order Code, Qty, Reel ID, PO#
Label with Cree Bin Code, Qty, Lot #
Copyright (c) 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
10
CLD-DS20 Rev 3
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp

▲Up To Search▲

Price & Availability of XPGWHT-L1-0000-00G51

	To Download XPGWHT-L1-0000-00G51 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .